Best Lab Equipment

Here are some more information for Magnetic Stirrer Stir:

Nonaqueous titration

Theory

Acid-base reactions

The theory is that water behaves as both a weak acid and a weak base; thus, in an aqueous environment, it can compete effectively with very weak acids and bases with regard to proton donation and acceptance, as shown below:

H2O + H+ H3O+

Competes with RNH2 + H+ RNH3+

or

H2O + B OH- + BH+

Competes with ROH + B RO- + BH+

The effect of this is that the inflection in the titration curves for very weak acids and very weak bases is small, because they approach the pH limits in water of 14 or 0 respectively , thus making endpoint detection relatively more difficult.

A general rule is that bases with pKa < 7 or acids with pKa > 7 cannot be determined accurately in aqueous solution.

Substances which are either too weakly basic or too weakly acidic to give sharp endpoints in aqueous solution can often be titrated in nonaqueous solvents. The reactions which occur during many nonaqueous titrations can be explained by means of the concepts of the Brnsted-Lowry theory. According to this theory an acid is a proton donor, i.e. a substance which tends to dissociate to yield a proton, and a base is proton acceptor, i.e. a substance which tends to combine with a proton. When an acid HB dissociates it yields a proton together with the conjugate base B of the acid:

HB

H+

+

B-

acid

proton

base

Alternatively, the base B will combine with a proton to yield the conjugate acid HB of the base B, for every base has its conjugate acid and, every acid has its conjugate base.

It follows from these definitions that an acid may be either:

an electrically neutral molecule, e.g. HCl, or

a positively charged cation, e.g. C6H5NH3+, or

a negatively charged anion, e.g. HSO4-.

A base may be either:

an electricially neutral molecule, e.g. C6H5NH2, or

an anion, e.g. Cl-.

Substances which are potentially acidic can function as acids only in the presence of a base to which they can donate a proton. Conversely basic properties do not become apparent unless an acid also is present.

Organic solvents

Various organic solvents may be used to replace water since they compete less effectively with the analyte for proton donation or acceptance.

Nonaqueous solvents used

Aprotic solvents are neutral, chemically inert substances such as benzene and chloroform. They have a low dielectric constant, do not react with either acids or bases and therefore do not favor ionization. The fact that picric acid gives a colorless solution in benzene which becomes yellow on adding aniline shows that picric acid is not dissociated in benzene solution and also that in the presence of the base aniline it functions as an acid, the development of yellow color being due to formation of the picrate ion.

Since dissociation is not an essential preliminary to neutralization, aprotic solvents are often added to 'ionizing' solvents to depress solvolysis (which is comparable to hydrolysis) of the neutralization product and so sharpen the endpoint.

Protophilic solvents are basic in character and react with acids to form solvated protons.

HB + Sol. Sol.H+ + B-

Acid + Basic solvent Solvated proton + Conjugate base of acid

A weakly basic solvent has less tendency than a strongly basic one to accept a proton. Similarly a weak acid has less tendency to donate protons than a strong acid. As a result a strong acid such as perchloric acid exhibits more strongly acidic properties than a weak acid such as acetic acid when dissolved in a weakly basic solvent. On the other hand, all acids tend to become indistinguishable in strength when dissolved in strongly basic solvents owing to the greater affinity of strong bases for protons. This is called the leveling effect. Strong bases are leveling solvents for acids, weak bases are differentiating solvents for acids.

Protogenic solvents are acidic substances, e.g. sulfuric acid. They exert a leveling effect on bases.

Amphiprotic solvents have both protophilic and protogenic properties. Examples are water, acetic acid and the alcohols. They are dissociated to a slight extent. The dissociation of acetic acid, which is frequently used as a solvent for titration of basic substances, is shown in the equation below:

CH3COOH H+ + CH3COO-

Here the acetic acid is functioning as an acid. If a very strong acid such as perchloric acid is dissolved in acetic acid, the latter can function as a base and combine with protons donated by the perchloric acid to form protonated acetic acid, an onium ion:

HClO4 H+ + ClO4-

CH3COOH + H+ CH3COOH2+ (onium ion)

Since the CH3COOH2+ ion readily donates its proton to a base, a solution of perchloric acid in glacial acetic acid functions as a strongly acidic solution.

When a weak base, such as pyridine, is dissolved in acetic acid, the acetic acid exerts its levelling effect and enhances the basic properties of the pyridine. It is possible, therefore, to titrate a solution of a weak base in acetic acid with perchloric acid in acetic acid, and obtain a sharp endpoint when attempts to carry out the titration in aqueous solution are unsuccessful.

HClO4 + CH3COOH CH3COOH2+ + ClO4-

C5H5N + CH3COOH C5H5NH+ + CH3COO-

CH3COOH2+ + CH3COO- 2CH3COOH

Adding HClO4 + C5H5N C5H5NH+ + ClO4-

Titration of halogen acid salts of bases

The halide ions - chloride, bromide and iodide - are too weakly basic to react quantitatively with acetous perchloric acid. Addition of mercuric acetate (which is undissociated in acetic acid solution) to a halide salt replaces the halide ion by an equivalent quantity of acetate ion, which is a strong base in acetic acid.

2R.NH2.HCl 2RNH3+ + 2Cl-

(CH3COO)2Hg(undissociated) + 2Cl- HgCl2 (undissociated) + 2CH3COO-

2CH3COOH2+ + 2CH3COO- 4CH3COOH

Visual indicators

The following indicators are in common use:

Indicator

Color change

Color change

Color change

basic

neutral

acidic

Crystal violet (0.5 per cent in glacial acetic acid)

violet

blue-green

yellowish-green

-Naphtholbenzein (0.2 per cent in glacial acetic acid)

blue or blue-green

orange

dark-green

Oracet Blue B (0.5 per cent in glacial acetic acid)

blue

purple

pink

Quinaldine Red (0.1 per cent in methanol)

magenta

almost colorless

Potentiometric titration

The end point of most titrations is detected by the use of visual indicator but the method can be inaccurate in very dilute or colored solutions. However under the same conditions, a potentiometric method for the detection of the equivalence point can yield accurate results without difficulty. The electrical apparatus required consists of a potentiometer or pH meter with a suitable indicator and reference electrode. The other apparatus consists of a burette, beaker and stirrer.

The actual potential of the reference electrode need not be known accurately for most purposes and usually any electrode may be used provided its potential remains constant throughout the titration. The indicator electrode must be suitable for the particular type of titration (i.e. a glass electrode for acid-base reactions and a platinum electrode for redox titrations), and should reach equilibrium rapidly.

The electrodes are immersed in the solution to be titrated and the potential difference between the electrodes is measured. Measured volumes of titrant are added, with thorough (magnetic) stirring, and the corresponding values of emf (electromotive force) or pH recorded. Small increments in volume should be added near the equivalence point which is found graphically by noting the burette reading corresponding to the maximum change of emf or pH per unit change of volume. When the slope of the curve is more gradual it is not always easy to locate the equivalent point by this method. However, if small increments (0.1 cm or less) of titrant are added near the end point of the titration and a curve of change of emf or pH per unit volume against volume of titrant is plotted, a differential curve is obtained in which the equivalence point is indicated by a peak.

See also

Titration

External links

Nonaqueous Acid-Base Titrations, Hardy Research Group, Department of Chemistry, The University of Akron

Further reading

Watson, David G. (2005) Pharmaceutical Analysis - A Textbook for Pharmacy Students and Pharmaceutical Chemists, Churchill Livingstone, 2nd Edition. ISBN 0-443-07445-3

Harris, Daniel C. (2007) Quantitative Chemical Analysis, W.H. Freeman, 7th Edition. ISBN 0-7167-7694-4

Categories: Titration
About the Author

I am a professional editor from
China Suppliers
, and my work is to promote a free online trade platform.
http://www.frbiz.com/ contain a great deal of information about

table linen runner
,
damask table runner

welcome to visit!

stirring shaft for mixing high viscous epoxy and tiny metal particles evenly?

Hi all...i am mixing epoxy ( viscousity 50,000 ) with tiny magnetic particles. I am using hand mixing.For small amount, there is no problem, but for larger amount I am facing some problems. most of the time metal particles are deposited at the bottom of container.It is importent for me to mix both evenly as I have to add controlled amount of magnetic particles. I can not place the shaft-end to be touching as there will be friction between shaft-end and bottom of container.but I place it as near as possible. What I need is to scoop up those deposited at bottom at certain frequency. I dont want to do it manually as the amount is large.Now I am using Anchor stirrer and still facing those kind of problems.Please recommend me some type of shaft which can mix material bottom to top..Thanks...

If you could make a part shaped like a propeller on the ends of your shaft it could mix the different layers together.

Scientific Industries Launches a New Product
BOHEMIA, N.Y. -- Scientific Industries , a leader in the design and production of shakers and vortex mixers, including the world-renowned Vortex-Genie, today announced the introduction of its MegaMag Genie LR, a magnetic stirrer designed to stir large volume containers up to 38 liters for applications requiring slow speeds ranging from 50 to 300 RPM.

Thanks for visiting!